Our Services

mold-inspection-services

Mold Inspection Services

At All Green Air, LLC we offer complete mold inspection, testing & reporting services.

Asbestos Survey

At All Green Air, LLC we offer complete asbestos survey, inspection, testing & reporting services.
asbestos-survey

The scope of the mold inspections:

  • We identify surfaces, displaying water damage and/or mold growth conditions to develop a remediation plan.
  • Take air samples for laboratory analysis as may be necessary to determine if indoor air quality is being affected mold growth conditions.
  • Take bulk samples for laboratory analysis to evaluate mold growth as may be necessary.
  • Take moisture measurements & evaluate water damage sources (eg. plumbing leaks , rainwater intrusion, condensation) in areas displaying water damage.
  • Recommend corrective actions or further evaluation.
  • After analysis, We will give you a verbal report of any preliminary findings approximately 24 hours after samples are sent to the lab. The written report is issued within 1-3 days after verbal report.

Our Mold Inspection Reports include a summary of our significant observations, test results, and site-specific remediation protocols that fully describe the necessary mold removal work. We also perform Clearance Assessments after remediation work is performed to determine if the mold remediation work was properly performed.

If you suspect that your indoor environment is contributing to your adverse health symptoms, respiratory problems or asthma-like symptoms, or if your asthma and allergies become significantly worse when you spend time indoors, then call us at All green Air, LLC to schedule a mold inspection. You may have a hidden mold problem.

Sampling Method

air-sampling
Air Sampling

Tape containing a slide coated with a sticky medium are placed at the end of a specially designed pump, which draws air in and collects airborne fungal spores.

Results of air sample will indicate mold levels and species.

A minimum of two tests are necessary for a comparison of interior air versus exterior air to determine if air quality is safe.

swab-test
Swab Test

Swab test involves a Q-Tip swab encased in a tube with liquid medium.

The swab is introduced to the visible mold on a surface.

The swab is then sent to the lab for analysis.

Swab sample results will indicate mold levels and species located in suspect area.

tape-lift
Tape Lift

This test involves a piece of tape, which is introduced to visible mold on a surface then placed on a slide for analysis.

The tape lift result will indicate species of mold located in suspect area.

bulk-sample
Bulk Sample

Bulk sampling is when an affected piece of building material is removed and sent to a lab for analysis (ie: carpeting, drywall, ceiling tile, etc.)

The bulk sample will indicate species of mold located on affected material.

Asbestos Testing Services

Air Sampling for Asbestos and Fibers

nygov-logo
  • Asbestos and Other Fibers by Phase Contrast Microscopy (PCM) - NIOSH Method 7400

    NIOSH method is used for the analysis of asbestos in air by PCM. Results are reported as fibers per cubic centimeter and depend on the volume of air sampled. PCM analysis is not asbestos fiber specific. It will count all fibers meeting the criteria for fiber determination.

  • Interim Transmission Electron Microscopy (TEM) Analytical Methods (Appendix A to Subpart E of Part 763)

    This method is used for the analysis of asbestos in air by TEM. Results are reported as structures per square millimeter and are specific for the determination of asbestos fibers present in the sample. This procedure is typically required for final re-occupancy criteria. Mandatory, Nonmandatory and Mandatory Sections to determine completion of response actions.

Bulk Sampling for Asbestos

  • Polarized-Light Microscope (PLM), NYS DOH ELAP 198.1

    This method is used for the analysis of asbestos in bulk materials by Polarized-Light Microscopy.

  • Polarized-Light Microscope (PLM), NYS DOH ELAP 198.6

    This method is used for the analysis of asbestos in Non-Friable Organically Bound bulk materials by Polarized-Light Microscopy. This method combines the tracked gravimetric-reduction preparation of 198.4 with the PLM point-counting of 198.1.

  • Transmission Electron Microscope (TEM), NYS DOH ELAP 198.4

    This method is used for the analysis of asbestos in Non-Friable Organically Bound bulk samples by Transmission Electron Microscope.

  • Revisions to ELAP Certification Manual for Analysis of Asbestos in Bulk Samples.

    Clarifications to NYS DOH ELAP methods 198.1, 198.4 and 198.6.

  • Polarized-Light Microscope (PLM) for Sprayed-On Fireproofing Containing Vermiculite (SOF-V) , NYS DOH ELAP 198.8

    This method is used for the analysis for Identifying and Quantitating Asbestos in Sprayed-On Fireproofing Containing Vermiculite Bulk Samples.

  • New Testing Requirements for Sprayed-on Fireproofing Containing Vermiculite (SOF-V)

    Announcement (July 22, 2014) of the availability of two NYS DOH ELAP-approved methods for the detection and quantitation of asbestos content in spray-on fireproofing that contains vermiculite:

    • NYS DOH's Item 198.8 and
    • RJ Lee Group's Method 055.

    Laboratories that would like to perform analysis for the detection and quantitation of asbestos content in SOF-V must seek accreditation for Item 198.8.

  • Vermiculite Interim Guidance Document

    This document (July 9, 2013) was developed through collaboration of the New York State Department of Health and the New York State Department of Labor.

Remediation Services

We do not perform remediation services ourselves because of a conflict of interest.

Our main objective is giving accurate results.

We do provide a scope of work, detailing the steps to correctly remediate the mold, and if needed we can refer qualified remediation professionals.

remediation

Protect your home with our professional mold inspections, mold detection, and mold testing services.